Antique brick is a popular wall decoration material in recent years. Its rich retro feelings, rough decoration techniques, and emphasis on the environment of furniture accessories make people enjoy leisure, warmth, nature, and unfettered visual enjoyment. The decorative effect is highly personalized. And taste. However, good products still require good construction methods and construction teams to lay out satisfactory results.
Roman Leo Tiles
Purchase First, choose the right product based on personal preferences, color matching of furniture accessories, house size, daylighting, age of family members, and appreciation habits. Taking into account the damage during the construction process and cutting corners, when purchased more than the actual area of ​​about 5%, so as not to produce different batches of products when the replenishment product color difference.
Pre-pasting preparation Before paving, please inform the construction personnel in detail, such as paving method, size of mortar joints, waist line, height of convex line, position of flowers, and toilets or kitchens with upper and lower equipments. Be sure to specify the tops of floor tiles. The models attached to the bottom and floor tiles should also be considered whether the size of the top and bottom and floor tiles should match. Once again, check whether the same color number and working size are marked on the product packaging box used in each room to avoid mixing and color mixing. If it is determined that the patchwork is laid, it is best to prepare a cross (or T-shaped) plastic colloid for positioning and a caulking agent that meets the desired color before laying.
Before the construction of the paving construction, the ground or wall shall first be leveled with a cement mortar, until it solidifies, and then the product shall be soaked with water to allow it to fully absorb water, then remove it, and coat it with a thin layer of white cement slurry. (The purpose of this is In order to prevent the penetration of black cement through the bottom of the blank into the glaze joint and thus affect the color effect of the product, the grout is evenly applied to the bottom of the tile to knock it out. It should be noted that the cement number is not the higher the better, the over 425 marked cement due to its excessive shrinkage force can easily lead to dry cement shrinkage when paving the product to drive the product to arch or even cracking. Within 1 to 1.5 hours after application, use a damp cloth or wood chips to thoroughly clean the cement stains adhered to the brick surface.
Cleaning and Maintenance In general, the cleaning and maintenance of antique tiles is more convenient. Just use a damp cloth or a mop to wipe them. If cement or rust stains left during the construction process cannot be removed, common industrial hydrochloric acid and water can be mixed 1:3 and wiped with a wet towel to remove stains.
In order to better reflect the use effect of antique tiles and the interior of the decoration, it is recommended that the wall tiles should be less than 3mm thick and the floor tiles should be over 3mm thick. In addition, the use of an appropriate color of the jointing agent for jointing treatment can play a more important role. This kind of paving method uses classical bricks without losing regularity, roughness, and softness. Naturally, there is no shortage of new interesting and warm romantic decorative artistic expressions.
Tile Floor Tile Furniture Brand Cement Decorative Furniture House Room Kitchen Wall Tiles Retro Furniture Antique Tiles Classical Furniture Tiles Tiles Kitchen Tiles
Steel bends and steel elbows are both very common pipe fittings which are used to change the flowing direction in a piping systems. In addition to pipe fittings for connecting , elbow pipe also refers to a processing method. It is to Bend the straight pipe through the processing method to achieve the purpose of changing the circulation direction of the pipeline. The manufacturing process and the finished product are called pipe bend.
In order to ensure that the wall thickness of the bending part is no less than that of the straight pipe part, the minimum radius of the pipe bending should be 3D( the D means nominal diameter of this bend). The specific size depends on the operating conditions. That is to say, radius is not restricted as long as it exceeds 3D, which can be 3D or 3.2D, even 4D, 5D, 6D and 8D are also acceptable. In addition, the angle of the bend can be in any degree, some times there are also custom-designed bends which are 22.5 °, 45 °, 90 °, 135 °, 180 °, 270 ° and so on.
ASTM A105,A234 WPB,Pipe Fitting Bend
Cangzhou Youlong Pipe Fitting Manufacturing Co., LTD , https://www.ypco88.com