Third, system debugging
CNC machine tool networking uses serial communication, while serial communication is characterized by information transmitted in one direction, occupying only one communication line. Therefore, this line serves as both a data line and a tie line (except for hardware flow control). , using the direct connection method of the tie line), that is, to transmit both the data information and the contact control information on one transmission line. To identify the contact signals and data signals in the information stream, it is necessary to have a serial communication protocol, that is, an agreement between the two parties, including the provisions of the transmission speed, data format, verification method and control character definition, communication Both parties must abide by it. By modifying the communication protocol, the eXtremeDNC software is suitable for almost all CNC systems.
The system debugging process is actually the process of modifying the controller properties (CSP). Users can find the corresponding communication parameters through the CNC system manual, and then set the “Setting†tab in the eXtremeDNC software to match, mainly set the communication port (CommPort), baud rate (BaudRate), data bit (DataBits). , StopBits, ParityBit, FlowControl. If you are unable to find these communication parameters, eXtremeDNC provides a connection wizard that allows you to detect communication parameters that match the controller.
The second is to set the path of the receiving and sending program (Path), the receiving label (Input), the sending label (Output), the remote request command (Remote), these settings are changed according to the CNC system, but not Complex, because the software itself provides a lot of options, you just have to choose according to the actual situation. When all these parameters are set, the CNC machine can communicate with the computer.
Fourth, the operation and use
After the system debugging is completed, the actual operation is very simple. You only need to open the computer and enter the main interface of eXtremeDNC every time you use it. Since the automatic connection is set, the software automatically connects with all CNC machine tools, and then it can be operated on the machine side. The machine operator does not need to operate the computer.
When the program is output to the computer, select the program to be output, directly use the OUTPUT (or PUNCH, DATAOUT, etc. depending on the CNC system) on the MDI operation panel, and the program will be output to the eXtremeDNC inbox (Inbox).
To call a program on your computer, you need to use a remote request file. The remote request file is actually similar to a simple NC program, which is saved in the program directory of the CNC system after debugging according to the type of CNC system. Each time you use it, change the program name in the remote request file to the name of the program to be called. Of course, the program name must be the name of the program existing in the Outbox, then send the remote request file, and finally use the MDI operation. The IUTPUT (or READ, DATAIN, etc., depending on the CNC system) on the panel is loaded into the desired program.
The following example illustrates the remote call process of the FANUCOTE CNC system:
(1) Open the remote request file O2222.
%
O2222
WWGETP program name WW
M30
%
(2) Modify the remote request file O2222 and change the program name to 3211.
%
O2222
WWGETP3211WW
M30
%
(3) Press the “OUTPUT†button to send the remote request file O2222 to the computer (this file is not saved in the inbox, just send a remote command to the computer).
Previous page next page
The 3D geonet vegetation slope protection technology not only significantly improves the overall and local stability of the slope, but also benefits the growth of slope vegetation. At the same time, the project cost is also low, which is in line with the development direction of slope engineering. Construction process: slope treatment-laying Three-dimensional net-spray planting-surface cover-maintenance management.
| Item | EM2 | EM3 | EM4 | EM5 |
| Mass per unit, g/m2 | ≥220 | ≥260 | ≥350 | ≥430 |
| Thickness, mm | ≥10 | ≥12 | ≥14 | ≥16 |
| Width, m | ≥2 | |||
| Length, m | ≥30 | |||
| Tensile strength(MD), kN/m | ≥0.80 | ≥1.4 | ≥2.0 | ≥3.2 |
| Tensile strength(CMD), Kn/M | ≥0.80 | ≥1.4 | ≥2.0 | ≥3.2 |
| Remarlc the special spec or size can be manufactured according to the demands of the contract oragreement. | ||||
1. It can protect earth from being eroded by winds and rains before grass growing up;
2. It can keep grass seeds distributed in slope firmly, and avoid to be washed;
3. Black mat can absorb thermal energy abundantly, increase ground wet, promote seed sprout, and prolong growth term of plants;
4. The surface is tough, so wind and water stream can form plenty of eddy in the surface of the mat, which can produce energy
dissipation function;
5. Plants can form composite protection layer and endure wash with high water and fast speed;
6. It can replace long-lasting slope protection materials such as concrete, pitch, block, etc., and can be used in slope
protection such as road, railway, river, dam, mountain slope, etc.;
7. It can reduce construction cost greatly;
8. It can prevent move of sand dunes after laying sand surface, which can improve roughness of the road surface, increase sediment
of the road surface, change physical performance, and improve partial ecological environment;
9. It is applied in slope protection of road, railway, mine and municipal construction, and it can prevent water and soil loss;
10. First choice of gardening, greening.
Q : Are you a factory or trading company?
A : We are a professional manufacturer that specialized in geomembrane, geotextile, Composite Geomembrane etc with ISO9001 certificate more than 15 years.
Q : Where is your factory located? How can I visit there?
A : Our facoty is located is No.10 Yuanshan Road High-tech Development Zone, Laiwu District, Jinan City China. You can take the plan to Jinan Yaoqiang International Airport, then we can pick you up.
Q : Could you send the sample before order confirmation?
A : Yes, we'd love to send a free sample to you for an evaluation if you need.
Q : How about the delivery time?
A : General within 3-7 days after received the deposit.
Q : Can you produce the product according to customers' requirements?
A : Sure, we are professional manufacturer, OEM and ODM are both welcome.
Q : Are you the Gold and Assessed supplier on alibaba?
A : Yes. We are the gold and assessed supplier on alibaba and has got the factory report by SGS.
3D Vegetation Net,Welding Set Geomembrane,3D Plastic Vegetative Cover,Welding Geomembrane Lining Material
Shandong Jinruixiang Geotextile Material Co., Ltd , https://www.jrxgeosynthetics.com