Everyone in the living room or bedroom and kitchen will be equipped with lights. For the choice of lights, the choice of different spaces is different. For example, in the living room, the living room is a relatively open place, and the lights used should be slightly decorative. The bedroom is closer to life, and the choice of the lamp is actually a matter of learning. Then everyone will follow the Xiaobian together to see the introduction of the wonderful content of the ceiling light .
First, the ceiling light construction process
(1) Using an electric drill to make a big eye in the ceiling;
(2) nailing wooden stakes into the pile eyes for fixing the wooden keel;
(3) Using 300*300 wood keel with 20*20 wood to fix the plasterboard;
(4) If you want to install the hole light, then you need to hang a little thicker, such as between 150 and 200, the side of the top of the top gypsum board, and you said that the top is vacant, a lot of ash, which is normal, such as When the gypsum board is nailed, the gypsum board will fall off. Even if the master cleans it, it will not be cleaned. Even if it is cleaned up, the side façade of the ceiling will be closed. It is not easy to repair the line, change the transformer, the lamp cup and the like. It is still empty.
Second, the ceiling lamp installation method
1. Preparation of materials:
(1) Construction materials: The following materials are commonly used.
1 wood (water tanks, wood strips, water panels of different specifications), aluminum alloy (plates, profiles), steel (steel, flat steel, steel), mainly used as supporting members.
2 plastic, plexiglass plate, glass as spacer, exterior veneer and heat sink, copper plate. An electrochemical aluminum plate is used as a decorative member.
3 other accessories such as screws, nails, rivets, finished lamps, adhesives, etc.
(2) Construction tools: pliers, screwdrivers, hammers, electric jigsaws, electric hammers, hand data, rulers, paint brushes, etc.
2. Operation steps:
1 First choose the location where the chandelier is installed, avoid the chandelier or the dark line buried in the ceiling.
2 Pre-embedded iron or wooden bricks in the structural layer, the buried position should be accurate, and there should be sufficient room for adjustment.
3 Set transition joints on iron and wooden bricks to adjust the error of the workpiece, which can be nailed, welded and screwed.
4 The boom and sling are connected with the transition piece.
3. Installation precautions:
If there are multiple chandeliers during installation, pay attention to their position and length. Install the chandelier at the same time as installing the ceiling. This can adjust the position and height of the lamp based on the ceiling joists. The method of direct discharge and casing can be used for the ceiling of the boom.
The method of adding the pipe is advantageous for the installation, and the roof panel can be ensured to be complete, and only the hole where the pipe is required to be taken out can be drilled. Straight out of the ceiling of the hanging cup, the board surface drilling is not easy to find. Sometimes it is possible to install the boom first and then cut off the panel to install the hole, but it has an effect on the decorative effect. The boom should have a certain length of thread for adjustment. Suspend the light box below the sling boom, pay attention to the reliability of the connection.
How about, I read the relevant introduction to the ceiling light, and I have learned a lot about the ceiling light. I hope that you can learn more about home improvement knowledge through this article, and you will be able to create a more perfect home environment. Thank you for reading this article and your support and love for Xiaobian. If you want to get more information about home improvement, please continue to pay attention to the decoration home network.
More related wonderful reading:
What brand of ceiling light is good? How to choose a ceiling light?
How to install the ceiling light? Ceiling lamp installation precautions
Living room ceiling lamp purchase tips living room ceiling lamp installation precautions
Integrated ceiling light, how to integrate the ceiling light
How to install the integrated ceiling light? Integrated ceiling light features
cryolite Basic Information
CAS: 15096-52-3
MF: AlF6Na3
MW: 209.94
EINECS: 239-148-8
Mol File: 15096-52-3.mol
Cryolite Chemical Properties
Melting point 1012
Boiling point decomp
density 2.9 g/mL at 25 °C(lit.)
Cryolite Application
Mainly used as aluminum smelting flux, insecticide, also used in glass, enamel, resin, rubber industry
chrysolite gemstone,chrysolite stone,chrysolite vertus,cryolife homograft,cryolite,cryolite 1856
ShanDong YingLang Chemical Co.,LTD , https://www.sdylhgtrade.com