What are the precautions for installing tempered glass doors?

Tempered glass doors are now widely used, whether in home improvement, hotels, or some office buildings, etc., there are tempered glass doors . Tempered glass doors are a more complicated kind of door materials, but they also have many characteristics. Then, let's take a look at the characteristics of the tempered glass door and the precautions for installing the tempered glass door!

Characteristics of tempered glass door

1. The tempered glass door has stronger security than the ordinary glass door. If the two glass doors are damaged by the outside world at the same time, the tempered glass will show honeycomb-shaped pure corner broken small particles, which will not be as full as the ordinary glass door. The ground is all, and it will not easily cause harm to the human body.

2. Compared with ordinary glass doors of the same thickness, tempered glass doors have higher strength, and the impact resistance and bending resistance are 3-5 times that of ordinary glass doors.

3. The tempered glass door has strong stability and can withstand a temperature difference of about 300 degrees, which is 3 times that of ordinary glass doors.

What are the precautions for installing tempered glass doors

1. Before installing the glass door, the verticality and elevation of the main support should be checked first to see if the height and levelness meet the requirements. Pay attention to the inspection of the installation holes. The U-shaped steel channel at the bottom of the glass should be fitted with neoprene rubber blocks at 1/4 width from the edge of the glass. Determine the number of suction cups according to the weight of the glass, and clean the glass and suction cups to avoid loose adsorption.

2. Assemble the support head and the glass on the installation platform. In order to ensure the airtightness and watertightness of the support, a torque wrench should be used to determine the torque according to the specific size of the support. When installing glass according to the standard, it should always be suspended on the two barges.

3. Look at the upper and lower parts of the installation where there are grooves, and which grooves are installed first. During installation, pay attention to slowly put the glass door into the groove, and then use a foam filler to fix the glass, at least 2 under each glass For block pads, the width of the pad is the same as the width of the notch, and it cannot be less than 100mm.

4. The position of the glass door installation and the size of the gap, the deviation should not exceed 2mm. After the glass door is installed, tighten the fastener and then fix it.

5. After installing 2 layers of glass doors, it is necessary to see if the overall elevation is flat, and the deviation of the plane cannot exceed 4mm. After confirming that there is no problem, you can seal with glue.

6. If you use an electric suction cup machine, it must be positioned well, and the left and right sides should be symmetrical, and can be offset above the center of the glass, so that it will not deflect left and right after being lifted. When trying to lift, lift the glass 2-3 cm to check whether each suction cup is firmly holding the glass.

7. When the glass is in place, check the verticality of the side of the glass to prevent the glass from colliding with the steel frame during lifting. Then, just check whether the glass is equal to the upper and lower gaps of the glass in place and meet the design requirements.

Xiaobian Summary: The above is about the characteristics of tempered glass door and glass door installation considerations which relevant content, we want to help at home, want to know more details, you can look on this website information.

What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount

If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.

Tempered glass door

Sanding Sponge


The surface of the sponge sand is sand, which is sponge inside. It has super softness and is suitable for grinding any irregular geometric curved surface. It is better to take it at the same time. Applicable to all kinds of models doll hardware electronic furniture plastic artificial stone polishing and polishing sponge sand paper elastic grinding sponge with special sponge as the substrate, a layer of mineral sand on the outside, so that the product maintains the original grinding effect, more flexible, good to take and dry Wet dual-use characteristics. Can achieve twice the result with half the effort in the injection molding industry. It can handle slips on the surface of injection molded products, raw edges, and can also be polished.

Sponge Polishing Pad555Sponge Polishing Pad607Sponge Polishing Pad613

kitchen nano emery magic clean rust removal sponge melamine sponge for a wide variety of curved, contoured or flat surface applications on wood, metal, paint, plastic, ceramics and drywall.the combination of flexible foam backing material and abrasive grit adhesion continually releases sanded material.Foam backing allows optimum pressure distribution to prevent sanding through surfaces,pressure spots are eliminated providing even surface pattern.Flexible foam allows adaptability to contours, shapes or areas of limited access,no folding or buckling results in an even pattern without scratching


We distributes and wholesales various brands of Bonded Abrasives, Abrasive Sanding Disc, Cutting Wheels , Flap Wheels , Flap Disc Backing Pad, Flap Disc Adhesive, and Surface Conditioning Product etc, and enjoy a high position among consumers.

Sponge Polishing Pad245Sponge Polishing Pad312Sponge Polishing Pad324Sponge Polishing Pad543


Sanding Sponge,Sanding Sponge Bunnings,Sponge Abrasive Pads,Gator Sanding Sponge

Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.jd-abrasives.com