First, the installation tool
Hammer, wood boring head, flat boring, edge planer, fine-tooth saw, screwdriver, level ruler, square ruler, tape measure, hanging hammer, electric drill, hole saw, poke, corresponding specifications drill.
Second, the installation materials
60 iron nails, self-tapping screws (40, 25), wood nails, small wood, 502 plastic, styrofoam, floor glue, door locks, door stoppers, hinges, wall damper materials, towels.
Third, the installation steps
1. Assemble the door cover
(1) Combined door pockets: According to the thickness of the wall, adjust the width of the corresponding door pockets. Use the 25mm self-tapping screws on the back of the door pockets to fasten the mining boards and adjustment boards. The spacing between the screws should not be greater than 250mm, the clearance between the mining plate and the adjusting plate should be less than 0.2mm.
(2) The top of the assembled vertical plate is sawed into the same plane, and it should be at an angle of 90° with the vertical plate.
(3) Saw notch on the top of the stand plate, the position and size of the notch must conform to specifications. The protruding door block of the top cover plate must be cut straight, smooth and smooth with a flat file, and can not have a hair edge.
(4) Combining the door top top board with the vertical board and pressing the top board cover on the vertical board. The protruding door block part of the top board is set in the concave part of the vertical board saw, both ends are used separately. Three or four 40mm wood screws shall be used for fastening. The mining port shall be on the same plane. The gap between the inner sleeve plate and the top sleeve plate at the inner side of the door sleeve shall be less than 0.2mm. The two upright plate and the top sleeve plate shall be 90°. The inner space size of the door pocket mining position: the width of the door is +7mm wide and the height is +13mm.
2, install the door cover
(1) Use a hammer to drill two rows of holes in the opening of the door (slightly inwardly inclined) with a spacing of 300 mm and fill it with a wooden needle of the appropriate size.(2) Put the assembled door cover into the door hole as a whole and use a small wooden bar to roughly fix the door cover. Both sides of the door cover should be on the same plane with the wall, and then check whether the whole door cover is vertical to the floor. Whether the two corners of the top plate and the two vertical plates are 90°.
(3) Use a speed-controlled electric drill (4.2mm drill bit) to drill the hole in the door cover, and then use 60mm nails to fix the door hinged page on the wall first, determine the size of the mining mouth, and then fix the other door cover. One side and the top set of boards, the two diagonal error should be less than 2mm. Because there is a gap between the door sleeve and the wall body, it can be filled with small wood strips and styrofoam, so that the door sleeve can be connected with the wall more firmly.
(4) Adhere to the noise barrier at the door pocket.
3, install the door leaf lock
(1) Open and close the page slot and unlock hole. Take care not to damage the finish of the door and other parts of the door pocket during the operation.
(2) Fit the door and install the door leaf. First screw a screw up and down on the hinge, then close the door to check whether the gap is the same, whether the opening is flexible, and then tighten the other screws after confirming the error. Do not use the screw to directly hit the door or the door.
(3) Install the door lock, and install the door lock to the corresponding position. The height of the lock position from the ground is generally 900-1000mm. After the installation, check whether the switch of the door leaf and the door lock is flexible and whether the left joint meets the specifications.
4, install door line
Straighten the edge of the door line saw to 45 ° oblique angle, using a wood planer for dressing, insert the right-angle edge into the door pocket groove, and use the floor glue to glue the door sleeve wire and the door jamming board.
5, install the door stopper in the corresponding position
After reading the above detailed process concerning the installation of solid wood doors, the decoration owners will be able to supervise whether the construction process is in line with the specifications when the wood door is installed, and no longer worry about the renovation of the door by the decoration company.
Tips: More practical decoration knowledge, real scene with the shoot, please pay attention to the palm of this site (micro signal: mall_jia).
Solid wood door installation
A hydraulic valve is a device used to control the flow and pressure of hydraulic fluid in a hydraulic system. It is typically made up of a valve body, which contains the necessary ports and passages for fluid flow, and a valve spool or poppet, which is responsible for regulating the flow of fluid.
Hydraulic valves can be classified into various types based on their function and design. Some common types include:
1. Directional control valves: These valves control the direction of fluid flow in a hydraulic system. They typically have multiple ports and can be used to control the movement of hydraulic cylinders or motors.
2. Pressure control valves: These valves regulate the pressure of the hydraulic fluid in a system. They can be used to maintain a specific pressure level or limit the maximum pressure.
3. Flow control valves: These valves control the rate of fluid flow in a hydraulic system. They can be used to adjust the speed of hydraulic cylinders or control the flow to different actuators.
4. Check valves: These valves allow fluid flow in one direction while preventing it from flowing back in the opposite direction. They are commonly used to maintain pressure in hydraulic systems or prevent backflow.
Hydraulic valves are essential components in hydraulic systems, as they enable precise control and efficient operation. They are commonly used in various industries, including manufacturing, construction, agriculture, and automotive.
Hydraulic Valve,Hydraulic Throttle Valve,Hydraulic Spare Part Throttle,Hydraulic Accessory Throttle Valve
Yantai Dongyue Hydraulic Technology Co., Ltd , https://www.deeleap.com