[Teach you a trick]
Medium-term payment time is pre-agreed
Early in the interim period, we must pay attention to its motives. Just a few days after the start of the work, the workers always said that they had to enter the material. There was no money, and the medium-term project had already arrived, urging the owners to pay the interim payments. Normally decorated workers will not do so, but the hapless "home improvement guerrillas" often use this trick.
Experts: When signing a contract, it is best to limit the foreman through money. This has been repeatedly proven to be the most effective. Moreover, what links and standards should be provided for what money should be provided so as to avoid mutual ambiguity. The proportion of payment is best based on the proportion of 3,331, so that even if there are problems, it can be stopped in time.
Buying gadgets also requires receipt
"Home guerrillas" will always find you at the scene and send you to buy it, which is a little cheaper. In fact, many parts are counted in the project section. The decoration foreman suffers from no opportunity to slaughter the owner. Once there is an opportunity, especially when the owner purchases the contracted materials, he will always give you a list. The wire is not enough. It takes 2 wooden lines, etc. Because the sub-secondary, so the owners also feel that the money is not too much, returning accounts is not enough meaning, especially male owners, generally do not account.
Expert: "Home guerrillas" will not be stupid enough to allow owners to take advantage of him, but they will definitely take advantage of the opportunity to take advantage of the loopholes, so despite the loss of such small parts, the money is not much, but the purchase is to buy , The account is still to be considered clear, encounter the foreman who loves to dip cheap, it is best to leave an invoice or receipt after each purchase, to avoid being difficult to open, hard to argue.
[process reminder]
"Hidden project" pays attention
The so-called "hidden project" is a construction project that has been concealed after renovation and cannot be seen on the surface. According to the renovation process, these "hidden projects" will be covered by the next process, so it is difficult to check whether the materials meet the specifications and whether the construction is standardized.
In recent years, due to the poor consideration of structural safety and fire prevention in the design and construction of home decoration projects, the following quality problems are likely to occur: As a result of the collapse of the ceiling in whole or in part, the ceiling becomes a “top dropâ€; Insufficient fixing of the package resulted in slumping; the leakage of the pipe caused damage to the ceiling; the buried route was buried under dangerous conditions; the substrate was not cleaned before painting, causing the paint to peel off and fall off.
Tiles should be soaked for half a day before use
The average home improvement will involve the decoration of the tiles. So what should we pay attention to when laying tiles?
Laying of wall tiles: Clean all types of dirt on the wall, and moisten one day in advance; Tiles must be soaked in clean water for at least two hours before the tiles are affixed. It is prohibited to stick with non-whole bricks when it comes to pipes, lighting switches, and bathroom equipment support.
The laying of ground tiles points: the tiles should be immersed in water for half a day before use, and bricks should not bubble; the kitchen and toilet should have a water gradient, no water, water does not flow back. Damage to the original waterproof layer during construction shall be treated with waterproofing. 12 hours of stagnant water test without leakage.
The quality inspection and acceptance points of the laying of the floor tiles must be firm, free of skew, warping, and empty drums; the overall surface is flat and the flatness error meets the allowable deviation requirements; the joints should be filled densely, straightly, evenly and width-wise, with no obvious dislocation.
ã€QC】
8 points for carpentry
Similarly, in the home improvement process, woodwork will inevitably be involved. What should be noticed when accepting carpentry?
1. Look at the gap: It is the wooden seal line, corner line, waistline veneer to meet the seam not exceeding 0.2mm, the line and the line mouth slot joint does not exceed 0.3mm, the veneer and the plate meet does not exceed 0.2mm, the sliding door The error of the entire surface does not exceed 0.3mm.
2. Look at the structure: whether the structure is straight. Regardless of horizontal or vertical orientation, the correct carpentry practices should be straightforward.
3. Look at the corner: Is the corner accurate? The normal corners are all 90 degrees, except for special design factors.
4. Look at the parquet: whether the spell is tight and accurate. The correct wooden pattern is to be seamless or to maintain a uniform distance.
5. See arc: whether arc and roundness are smooth and sleek. In addition to a single, a number of the same shape to ensure consistency in the shape.
6. Look at the door: Is the cabinet door switch normal? When the door is open, it should be light and no noise.
7. Look at the leveling: The surface of the woodworking project should be flat, without drumming or breaking.
8. Look at symmetry: Symmetric woodwork items are symmetrical.
4 methods to control the quality of paint
Of course, the choice of paint is also very important. At present, there are many kinds of paints on the market. When choosing, you should pay attention to the following aspects:
To buy the heaviest package: lift up the paint bucket and shake it. If there is a crackling sound, it means that the packaging is seriously inadequate, there are two shortages, and the degree of adhesion is too low. The formal factory is real and can hardly hear the sound.
Estimate the amount of use: Buy one time to buy, so as not to have a slight color difference.
Choose the same brand: primer and topcoat are best to use the same brand or matching paint to prevent chemical reaction between primer and topcoat.
Standardize the construction sequence: remove dust and dirt on the surface of wooden products and lines (wood base layer); repair burrs on the surface of wooden base layer, lift defects, etc., use sand leather to polish, make corners neat; use oily putty (or transparent putty) for batch After scraping, polishing, and replenishing the putty, use the varnish to make up the brown eyes and nail holes and do the partial color correction work. Apply the paint over the first pass, reapply the putty, and remove the surface dust after polishing. After the paint is applied twice, the dust on the surface is removed after polishing, and the water is used to grind with the sand skin to repair the part of the hanging oil. The paint is applied the third time until the desired effect is achieved.
Summer decoration knowledge Three trees paint entrance decoration paint home decoration design switch paint kitchen sliding door cabinet door kitchen cabinet door bathroom sliding door bathroom tile bathroom door bathroom ceiling material bathroom ceiling overall bathroom toilet design bathroom waterproof bathroom floor tile kitchen tile balcony tile ceramic tile specifications
10W Mini Glue Gun Ptc Heating Features:
1. Versatile
2. Easy
3. Quick
4. Proective Nozzle Cover
5. Trigger Flow Control
6. Bonds instantly
7. High quality
8. High temperature or low temperature
Idea for many applications. Fastening various materials such as paper, cardboard, fabric,wood, lace,trims,leather,metal,glass, tiles, rubber, ceramics and flooring etc. Ideal for hobby and household repair,DIY&craft projects.
Designed and manufactured to the highest of standards to ensure a robust and long life, we hope it provides you with many years of trouble-free, safe and reliable service.
General Safety Information:
1. Check if the plug cord was in good condition, and if there is stand before plug into the electrical outlet ; Check if the used glue gun has glue flow through back of the tunnel;
2. wait 5-10 minutes to allow glue to soften, stand up the glue gun on the table when not in use;
3. Touch nozzle to any clean, dry surface you wish to bond, to avoid any impurity stop the nozzle;
4. If the glue could not flow from the nozzle when the glue gun start to work, check if the glue gun are heating;
If glue
gun can not be heated, there are following reasons:
1
Plug cord into electrical outlet not
properly;
2
Glue gun has been destroyed owing to
inner cord short circuit;
If glue gun can be heated, there are following reasons: Nozzle has been stopped by any impurity, ask careerman to manage it.
5. Do not use the glue gun under moist climate, humidity will affect insulation and cause electric shock;
6. Do not touch the nozzle or melted glue;
7. Do not remove out the melted glue stick from the tunnel back side, it will damaged the glue gun as well as scalding person hands.
8. Do not to disassemble or assemble any glue gun accessories freely, it will cause glue gun do not work properly;
9. Keep out of reach of children and stocked it beyond any of Children palpable side;
10. Only used for melting glue stick, no other usage;
11. When in use, there are any glue flow back from tunnel, stop using immediately, wait for careerman clean the glue;
12. Close the power if the glue gun not in use after 15 minutes;
Important Caution:
1． Before use the glue gun, check if the plug cord into electrical outlet properly;
2． When glue gun in first use, the heating element will have small smoke, it is normal situation, but the smoke will disappeared after 10 minutes;
3． After power, not for a long time in standby mode(not longer for 20 minutes), when the suspension of use, unplug first.
4． Avoid to use the glue gun under very hot or very cold environments.
5． Better not work under direct cold wind blowing, it will reduce efficiency and loss power
6． When in continuous using, do not press the trigger with great pressure, and try to squeeze out the un-melted glue, it would damage the glue gun
7． Not applicable for bonding heavy objects or objects needed strong adhesive
8． The quality of glue stick will directly influence the glue gun function and sticking objects quality;
9． If the power cord is damaged, do not replace it by yourself, must ask for professionals to replace it.
10． This tools must b e placed in its position when not in use. And storage before the tools complete cooled.
11． Be careful when using any other electrical appliance with flammable material.
12． Not applicable for a long time in the same place.
13． Do not use an explosive gas atmospheres.
14． Note that heat may be the line of sigh, combustible materials.
15． Do not leave equipment unattended when switched on.
16． This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
17. Children should be supervised to ensure that they do not play with the appliance.
Using methods
1. Glue gun using voltage is 110-220V AC,50/60Hz;
2. Tip gun forward on stand and place a piece of cardboard under the nozzle
3. Use 7-8mm
(mini trigger glue gun), 11-12(big trigger glue gun), insert glue sticks
through
tunnel at back of gun
4. After power, wait for 5-10 minutes to allow glue to soften
After glue softens, squeeze trigger to feed glue through glue barrel. Excessive force will damage glue gun. Put down nozzle after work, disconnect the power plug
Mini Glue Gun
10W Mini Glue Gun, Mini Glue Gun, Small Glue Gun, Electric Glue Gun
Ningbo Kingvos Electrical Appliance Co.,Ltd , http://www.kingvos.com