Diesel generator sets are the providers of emergency backup power after the mains failure. Most of the time, the unit is in standby standby state. Once the power is cut off, the unit is required to start in an emergency and supply power urgently. Otherwise, the standby unit will lose its meaning. How can I achieve this? Practice has proved that strengthening daily maintenance is the most cost-effective method. Because the unit is in a static state, various materials of the unit itself will undergo complex chemical and physical changes with engine oil, cooling water, diesel oil, air, etc. Bad".
1, the unit start battery failure
The battery is unmaintained for a long time, and the electrolyte does not get replenished in time. The battery charger is not configured. The battery is discharged after a long period of natural discharge, or the charger used needs to be manually charged and floated. Due to the negligence of the switching operation, the battery power is not required. To solve this problem, in addition to configuring a high-quality charger, necessary inspection and maintenance is necessary.
2. Water enters the diesel engine
As the moisture in the air condenses in the temperature change, the water droplets are attached to the inner wall of the fuel tank and flow into the diesel oil, causing the diesel water content to exceed the standard. Such diesel oil enters the engine high-pressure oil pump and will corrode the precision coupling parts----- The plunger can seriously damage the unit, and regular maintenance can be avoided.
3, the retention period of the oil (two years)
The engine oil is mechanically lubricated, and the engine oil has a certain holding period. When stored for a long time, the physical and chemical properties of the oil will change, causing the lubrication condition of the unit to deteriorate during the operation of the unit, and it is easy to cause damage to the unit parts, so the lubricating oil should be replaced regularly.
4, three filter replacement cycle (wood filter, machine filter, air filter, water filter)
The filter is used to filter diesel oil, oil or water to prevent impurities from entering the body. In diesel, oil and impurities are inevitable, so the filter plays an important role in the operation of the unit, but At the same time, these oils or impurities are deposited on the wall of the filter to reduce the filter capacity of the filter. If the deposit is too much, the oil path will not be unblocked, so that the oil machine will be shocked when the load is running, because the oil cannot be supplied. Oxygen), so during the normal use of the generator set, we recommend: First, the common unit replaces the three filters every 500 hours; second, the standby unit replaces the three filters every two years.
5, cooling system
The water pump, water tank and water supply pipeline have not been cleaned for a long time, so that the water circulation is not smooth, the cooling effect is reduced, the water pipe joint is good, the water tank and the water channel are leaking, etc. If the cooling system is faulty, the consequences are: first, cooling The effect is not good and the water temperature in the unit is too high and the machine is shut down. The Weir letter unit is the most common. Second, the water tank leaks and the water level in the water tank drops, and the unit will not work properly. (To prevent the water pipe from freezing when using the generator in winter , we recommend that it is best to install a water heater in the cooling system).
6, lubrication system, seals
Due to the chemical properties of the lubricating oil or oil ester and the iron filings generated after mechanical wear, these not only reduce its lubricating effect, but also accelerate the damage of the parts, and at the same time, due to the corrosion of the rubber sealing ring, the oil seal It is also aging at any time and its sealing effect is reduced.
7, fuel, gas distribution system
The output of the engine power is mainly that the fuel is burned in the cylinder and the fuel is sprayed through the injector. This causes the deposited carbon to deposit on the injector. As the amount of deposition increases, the fuel injection amount of the injector will be limited. The effect is that the ignition timing of the injector is not accurate, the fuel injection amount of each cylinder of the engine is not uniform, and the working state is not stable. Therefore, the cleaning of the fuel system and the replacement of the filter components are smoothly carried out. The adjustment of the gas system makes it evenly ignited.
8, the control part of the unit
The control part of the oil machine is also an important part of the maintenance of the unit. The unit is used too long, the line joint is loose, and the AVR module works normally.
Concerned about surprises
Label: Why do diesel generators need regular maintenance?
Previous: The working principle and operation flow of the sealing machine Next: Talking about the molding and use details of the cold box mould
Industrial sectional doors are the most durable and longest lasting doors to ensure circulation at the areas of the factory entrance and exit of goods, loading and unloading areas.
The body of sectional door is forming by 40 mm sandwich panels. These panels provides sound and heat insulation due to the intense doped polyurethane insulation was injected between galvanized steel sheet. (50 kg/m3).
Industrial sectional door systems provide space-saving with opening parallel to the ceiling.Any opening can be used clearly . and produces in accordance with the transition range and the height in the factory buildings or warehouses.
Doors is working sliding by be the most appropriate the gap between the top level of the gate with a ceiling height within the side rasils. The door can be mounted in different ways according to the gap distance (standard, low, highlift and vertical track systems).
Industrial sectional doors can easily be opened automaticly by 230-380 V-AC/50 Hz electric motor or manualy thanks to torsion spring system that balances the weight of the door.The galvanized springs are made to be durable of 25.000 door cycles.Motor with emergency chain All the drive systems have a mechanical back-up system fitted to the reduction gearbox of the electric motor, so that the sectional door can be opened if the power fails. The reduction gearbox can then be powered using the chain.
Industrial Sectional Door,Industrial Overhead Sectional Door,Industrial Warehouse Sectional Door,Industrial Garage Interior Sectional Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hffreezerdoor.com