With the progress of the times, people’s aesthetic consciousness has been continuously improved, and the style design of lamps and lanterns has become increasingly personalized. The installation of home lamps is no longer confined to the previous single style, and the embedded ceiling lamps have a good lighting effect due to their good lighting effect. Atmosphere construction has played a significant effect and has been loved and supported by the majority of consumers. Although embedded ceiling lamps are now widely used, most people do not understand the installation of embedded ceiling lamps. The following is a small series of embedded suctions. The top light installation specific introduction, together with the small series to see it.
First, embedded ceiling lamp installation steps and methods
1, embedded ceiling lamp installation steps
(1) Open one hole at the ceiling installation
A hole will be opened in the place where the ceiling lamp needs to be installed to facilitate the installation of the ceiling. Determine the location of the ceiling lamp. The size of the hole corresponds to the English ceiling area.
(2) When installing, firstly install the installation card to the lamps on both sides
The card is used to defensive lamps on both sides and the lamp is installed inside a square hole or a round hole.
(3) Connect the power cable, cover the cable cover and tighten it with screws
The number of fixed lampholder bolts should not be less than the number of fixing holes on the base of the lamp, and the diameter of the bolt should match with the aperture; there is no lamp with fixed mounting holes on the base (perforated when installing), and each lamp is used for fixing bolts Or the screws should not be less than 3, and the center of gravity of the lamp should be consistent with the center of gravity of the bolt or screw.
(4) Put on the fixture and fix it
Double-clamp the clamps on both sides of the lamp and insert it into the ceiling opening. The inner circlip presses against the ceiling. Press the mask with your hand and push the clamp a little harder.
2, embedded ceiling lamp replacement steps
(1) Press the open face of the mask by hand, the mask will automatically spring open, and take the lower cover.
(2) Pull out the bad lamp slightly.
(3) Put the new copper tube on the four holes of the quasi-socket and insert it with a little force. Note: Lamps vary by model.
(4) Put the mask in the direction of the cover into the base, press the card into place with a little force. If it is not properly installed, it will cause the lamp shade to fall.
Second, embedded ceiling lamp installation precautions
1. Ceiling light can not be directly installed on flammable objects. Some people use paint to paint behind the ceiling lamp in order to have a beautiful ceiling. In fact, such a practice is very dangerous. If there is no heat insulation when installing the ceiling lamp, it will be very dangerous in the future use. If the surface temperature of the luminaire is too high near the flammable material, heat insulation or heat dissipation measures must be taken to prevent the occurrence of fire.
2. To make the packaging of the cable, in order to use the lamp safely, the two wires connected to the ceiling lamp should have good electrical contact. They need to be wrapped separately with insulating tape and keep a certain distance. If possible, do not try to Place both ends under the same piece of metal to avoid the danger of a short circuit. Insulation tapes need to be bought with good quality products. Never buy inferior tapes.
3. The power supply should be disconnected during installation. When the embedded ceiling lamp is installed, the power valve it controls should be closed to avoid electric shock. Some desiccants can be placed in the lampshade. Especially when the ceiling lamp in the bathroom is installed, some desiccant should be placed to prevent the wet environment from affecting the use of the circuit.
4. Before the embedded ceiling lamp is installed, the cross section of the wire core of each lamp needs to be inspected. The cross-sectional area of ​​the copper core of the wire cannot be less than 0.75 mm. The copper wire with enough thickness can ensure the safety of the lamp. The connection between the wire and the lamp head should be firm, and the electrical contact should be good so as not to cause sparks on the wire and the terminal due to poor contact, thereby causing danger.
Third, embedded ceiling applicable scope
1, embedded ceiling home
Household embedded ceilings are suitable for installation in kitchens, bathrooms, balconies, aisles.
2, embedded ceiling lamp engineering
The project is more suitable for ceilings, gypsum board ceilings and wooden ceilings. In advance, a hole should be opened above the hanging board that needs to be installed. The two steel cards of the lamp are installed at both ends of the lamp. After the power cord is connected, it can be directly embedded.
Xiao Bian concludes: About embedded ceiling installation knowledge is introduced here, and hope to be helpful to everyone. If you want to know more related information, you can pay attention to this website information.
Built-in ceiling lamp Ceiling lamp Installed Oupu Ceiling lamp Kitchen Ceiling lamp led Ceiling lamp What makes a good brand
A flange can also be a plate or ring to form a rim at the end of a pipe when fastened to the pipe. A blind flange is a plate for covering or closing the end of a pipe. A flange joint is a connection of pipes, where the connecting pieces have flanges by which the parts are bolted together.
Although the word flange generally refers to the actual raised rim or lip of a fitting, many flanged plumbing fittings are themselves known as 'flanges':
There are many different flange standards to be found worldwide. To allow easy functionality and interchangeability, these are designed to have standardised dimensions. Common world standards include ASA/ASME (USA), PN/DIN (European), BS10 (British/Australian), and JIS/KS (Japanese/Korean). In the USA, ANSI stopped publishing B16.5 in 1996, and the standard is ASME B16.5
Flange And Fitting,Vacuum Flanges and Fitting,Steel Pipe Flanges and Fittings,Flange Clamp and Flange Fittings
Yixing Steel Pole International Trading Co., Ltd , https://www.yx-steelpole.com