| Home>Bearing knowledge>Renovation bearing grease capping machine |
Modified bearing grease capping machine
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
The drawing scheme is carefully analyzed and discussed in the technical difficulties presented during the bearing installation process. The uniform grease capping machine is optimized and depicted.
(1) Change the layout and support surface of the gland cylinder; add the support strength and rigidity of the system; ensure the system under frequent pressure shock; can adhere to better centering accuracy.
(2) The original double motor drive homogenization is changed to single motor drive homogenization; the whole machine layout is compact; the axial scale is reduced; the floor space is reduced; and the energy consumption is greatly reduced.
(3) Adjust the stroke of the cylinder; ensure that the bearing gland is greased and then pushed to the specified orientation of the material channel by the reset cylinder;
(4) In the organization depiction; the elastic organization is added; before the gland; the two sides of the grease conflicting piece under the effect of the spring force; the pre-positioning of the bearing is first performed (the conflicting piece is spline-guided; the centering is accurate); The bearing does not deflect during the movement; together, it can prevent the problem of gland deflection caused by inaccurate loading.
The working principle is shown in the drawing; the sealing cover assembly is placed in the gland seats 4 and 6 on the left and right sides. When loading, the bearing inner assembly rolls to the orientation as shown. The gland cylinder piston 2 is rightward under the pressure oil effect. Move; the grease conflicting sheet 5 first touches the left end of the bearing assembly; the thrust bearing inner component moves to the right. Then; the right end of the inner component touches the right side conflict piece. Then; the spring is tightened and the internal component is finished with a certain pressure. Position, move to the right; carry out the gland; announce the signal when the block 3 presses the travel switch K2; indicates that the gland is finished. The motor drives the pulleys 1 on both sides; the torque is transmitted through the spline shaft; The inner ring of the bearing rotates; the end is greased. The grease is adjustable at 0~3min; the grease spindle speed is 150r/min. After the grease is fixed; the cap cylinder piston 2 is retracted; when the block is pressed, the stroke switch K1 is announced. The reset cylinder piston 7 moves to the left under the effect of the pressure oil; the bearing after the gland is pushed back to the initial orientation under the effect of the reset cylinder, the reset cylinder piston retracts; the release stroke switch K3 announces the signal; the workpiece is unloaded; Go to the next cycle.
The conclusion is improved by the description of the uniform grease capping machine; when the function of the pressure cap is equalized; the principle of the action is more scientific and more reasonable; the pressure deviation and misalignment problems in the gland process are dealt with; the quality of the gland is ensured and The loading and unloading is smooth; together; greatly reducing energy consumption; increasing production power.
Recommend to friends comments close window
| Bearing related knowledge |
| Selection of low-noise bearings The common terminology of rolling bearings is the definition of the use of bearings - mining and processing how to choose the basic requirements of the quality of the training of sliding bearing oil bearing steel |
This article links to http://
Please indicate the bearing network http://
Previous:Staining of fine graphite seal ring of SKF bearing Next:The bearing material without smooth bearing (1)
Residential Sectional Garage Door
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers. The door is balanced by either a torsion spring system or a pair of extension springs.A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security
• Aluminum garage doors are low-cost, light, rust-proof, and feature low-maintenance. They are prone to denting because aluminum is not strong and they are energy-inefficient since aluminum is a highly conductivematerial.
• Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
• Steel doors have become common and are available in a variety of sizes and styles, provide strength and security, are cost-competitive, and may have optional insulating value. Extra strength is available with two or three layers of galvanized steel with a low gauge number (23-24 gauge steel panels).
• Wood garage doors offer aesthetic appeal, but they are high-maintenance and may be expensive. Low-priced wood garage doors may warp and break easily.
Residential Sectional Garage Door,Automatic Metal Sectional Garage Door,Standard Lift Garage Door Drum,Polyurethane Foam Garage Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.pvchighspeeddoor.com