Wall waterproofing is the basic stage of renovation. Wall waterproofing is difficult to deal with after a water leakage occurs. The waterproof mechanism of waterproof coating can be divided into two types: one is to form a complete coating to block the penetration of water or penetration of water molecules; the other is to prevent the moisture from passing through the hydrophobic effect of the coating itself. . Do you know how to waterproof a wall? The following Xiao Bian will introduce you to the practice of wall waterproofing and the points of attention for waterproof construction.
Waterproof principle
The waterproof mechanism of waterproof coating can be divided into two types: one is to form a complete coating to block the penetration of water or penetration of water molecules; the other is to prevent the moisture from passing through the hydrophobic effect of the coating itself. . After the polymer composite coating is cured, it can form a complete and continuous paint film. The width of the molecular gap is about several nanometers, and a single water molecule can pass through these gaps, but the natural water is usually in an associated state, dozens of Due to the hydrogen bonding between water molecules, a large water molecule group is formed. It is actually difficult for the water molecule group to cure the gap between the paint films through the polymer coating. This is the main function of the water-proof coating film which is waterproof. the reason.
Wall waterproof practices:
1, base surface treatment is the basis
Base surface treatment is the key to waterproof construction. The base surface must be cleaned before construction to ensure that it is strong, flat, clean, free of dust, grease, wax, mold release agents, and other debris, such as voids, cracks, and other defects. , It must be repaired and leveled with cement mortar in advance, and the yin and yang angles should be rounded. Keep the base moist when there is no clear water.
2, brushing method should pay attention
Brushing force is uniform, be careful not to miss the brush; before and after the two times brushing to maintain the vertical intersection angle, in order to fully cover in place; single brushing should not be too thick, especially the nozzle and corner, can not exceed 1mm, to prevent dry After the solid cracks.
3, maintenance, protection is also important
After 24 hours of construction, it is recommended to use a damp cloth to cover the coating or spray water to cure the coating. Before treading, rainwater, sun exposure, and sharp damage are prohibited before it is completely dried. In particular, special care must be taken not to damage the waterproof layer during the subsequent installation of the sanitary ware.
4, carefully check the prevention and after suffering
Brushing must be meticulous, carefully check after brushing, especially the joints, yin and yang angle, nozzle and other parts; after the completion of the construction to do closed water test for 48 hours, close the water height as much as possible, not less than 20cm, carefully Check whether there is any traces of water or water on the ceiling below the floor. The light wall should be tested for water and check the back wall.
Waterproof construction points
1, waterproof coating to meet the thickness requirements of the premise, the number of brushing the more, the better the density of the film, so brushing should be brushing many times, whether it is thick waterproof coating or thin waterproof coating Do not paint once.
2. Each time brushing should be uniform, there must be no exposed, leaked and stacked phenomenon. When brushing many times, it should be dried and filmed before coating.
3. When the roof slope is less than 15%, the carcass reinforcement material shall be laid parallel or perpendicular to the roof, which shall be determined by the convenience of construction. When the roof slope is greater than 15%, in order to prevent the carcass reinforcement material from sliding down, it should be laid perpendicular to the ridge. When laying parallel to the ridge, it must be laid up from the lowest elevation, and the carcass reinforcement is lapped in the direction of the flowing water to avoid drowning. When carcass reinforcement material is applied, it should be brushed and applied to avoid separation.
4, in order to ensure the integrity of the coating waterproof layer, the long side of the carcass lap width should not be less than 50mm, short-edge lap width should not be less than 70mm, there is no need to press the waterproof web to meet the width requirements.
5. When using two layers of carcass reinforcement material, the upper and lower layers shall not be laid vertically, so that the two layers of carcass material have the same extension in the same direction; the upper and lower lap joints shall be staggered, not less than one-third width , To avoid heavy seams on the upper and lower carcass reinforcements and uneven thickness of the waterproof layer.
The above points are the information on the practice of waterproofing the walls and the points of attention for waterproof construction summarized by everyone on this site. I believe we will have a certain understanding after reading them. This way, everyone will know a lot, if everyone There are those who want to know can check it out on our website.
Wall waterproof metal wall waterproof membrane wall waterproof steel structure wall waterproof wall waterproof grade
Chain Link Fence: A chain link fence is a type of woven fence made from galvanized or PVC-coated steel wires. It consists of a series of interlocking diamond-shaped openings formed by the woven wires. Chain link fences are popular due to their affordability, durability, and versatility. They are commonly used for residential, commercial, and industrial applications, such as property boundaries, security enclosures, sports fields, and animal enclosures.
Diamond WIRE MESH: Diamond wire mesh, also known as diamond wire netting or chain link wire mesh, is similar to a chain link fence. It features a diamond-shaped pattern created by the interlocking woven wires. Diamond wire mesh is available in various materials, including galvanized steel, stainless steel, and PVC-coated steel. It is widely used for applications such as fencing, animal enclosures, construction site barriers, and agricultural applications.
Cyclone Wire Mesh: Cyclone wire mesh is another term used for chain link fence, particularly in certain regions or countries. It refers to the same type of woven fence made from interlocking galvanized or PVC-coated steel wires, forming a diamond-shaped pattern. Cyclone wire mesh is commonly used for fencing, security purposes, and other applications where a durable and cost-effective solution is required.
Chain Link Sport Fence: A chain link sport fence is a specialized type of chain link fence designed for sports facilities such as tennis courts, baseball fields, or soccer fields. It provides a secure and visible boundary for the sports area while allowing spectators to easily view the action. Chain link sport fences are typically constructed with a higher gauge wire and smaller mesh size compared to standard chain link fences to prevent balls from passing through and to enhance player safety.
These different types of fences, including chain link fences, diamond wire mesh, cyclone wire mesh, and chain link sport fences, offer various levels of security, visibility, and functionality. The specific choice depends on the intended application, budget, required durability, and aesthetic preferences.
Chain Link Fence,Diamond Wire Mesh,Cyclone Wire Mesh,Chain Link Sport Fence
Hebei Aibuer trading co., Ltd , https://www.ablehardwares.com