First, the ceiling lamp installation notes
Most of the ceiling lamps are mainly flat, and they are installed close to the roof, just as they are absorbed on the ceiling. The ceiling lamp is particularly suitable for use in halls, corridors, kitchens, bathrooms, bedrooms, etc. due to its small space and light intensity.
Ceiling light installation method
1, ceiling lamp fixed
First place the chassis on the roof, draw a hole on the fixed location, and use a percussion drill to make a hole in the location to be installed. Use a hammer to fill the hole with a fastener such as an expansion screw. It should be noted that the bearing capacity of the fastener should match the weight of the ceiling lamp to ensure that the ceiling lamp is fixed firmly.
2, ceiling lamp wiring
Remove the roof wire from the hole in the chassis and secure the chassis with the screw in the above position. After fixing, connect the wires to the wires of the chassis. Wrap the exposed wires in the area with insulating tape. Finally, attach the lamp and lampshade.
Ceiling lamp installation notes
1, pay attention to safe punching standards
For the safety of the family, if there is no special requirement for the fixtures, the wall openings are generally 6 mm. When installing the impact drill, install a matching drill. When drilling, pay attention to the drilling depth and ensure that the expansion screws are fully accessible.
2, pay attention to the power line security
The end of the cable connected to the ceiling lamp power supply line should have good electrical contact. It is best to wrap it with black tape and keep a certain distance. If possible, try not to put the thread under the same piece of metal to avoid the danger of short circuit.
Second, chandelier installation notes
The chandelier is a high-grade decorative lighting used on the indoor ceiling. Its noble and noble styling can highlight the grandeur of the house. The use of a chandelier requires that the house has a sufficient level of floor height, which is required to be more secure due to the weight of the chandelier.
Chandelier installation method
1ã€Chandelier fixed
Similar to the ceiling lamp, the chandelier must first be drilled, drilled using a percussive drill, and then inflated with an expansion screw. It is noteworthy that since the weight of a pendant lamp is generally larger than that of a ceiling lamp, a metal hanging plate or hook is used to fix the ceiling first, and then the base of the pendant lamp is connected, so that the installation of the pendant lamp can be more secure.
2, pendant light connection
Screw on the head screws and the base is installed. Connect the power cord. The exposed part of the copper wire is wrapped with insulating tape. Then connect the boom to the base and adjust the height. Finally, the lampshade of the pendant lamp and the lamp can be installed.
Chandelier Installation Notes
1, pay attention to the chandelier can not be installed too low
The use of a chandelier requires that the house be of sufficient height. The chandelier, whether installed in the living room or in the dining room, cannot be hung too low to be such that it does not obstruct the normal line of sight or feels harsh to the eye. Generally, the height of the derrick can be adjusted. If the house is low, using a ceiling light will make the house more bright and generous.
2, pay attention to the chassis fixed and secure
The basic requirement for lighting installation must be firm. When installing various types of lamps, install them according to the requirements of the lamp installation instructions. If the weight of the luminaire is greater than 3kg, a pre-embedded hook should be used or the roof hanger should be directly fixed with an expansion bolt.
3, check the boom is firmly connected
Generally, the suspender of a pendant lamp has a certain length of thread and can be used for adjusting the height of the hanger. In addition to careful inspection of the installation of the chassis after the installation is solid, sling suspended below the light box, should pay attention to the reliability of the connection.
Third, spotlight installation precautions
The spotlight is a lamp installed in a small space. Since it depends on reflection, it can produce very strong light with little power. Can be used to highlight a place in the room, can also increase the three-dimensional, creating a special atmosphere. Here's what to look for when installing a spotlight.
Spotlight installation method
1, plan to reserve spotlight position
Spotlight installation method is mainly embedded installation, generally according to the renovation plan to reserve lines, so that the decoration workers will open a good hole in the ceiling, the appropriate set aside the searchlight empty slot.
2, spot light connection
Attach the base to the empty slot of the spotlight, pull out the wire, and fix the screw. Connect the wire ends, and at the same time, do not forget the insulation treatment. Finally, install the spotlights.
Spotlight Installation Notes
1, pay attention to spotlight line need to install the transformer
Although spotlights have energy-saving, high brightness, and strong decorative effects, they also have the disadvantage that they cannot be ignored, that is, the voltage is unstable and can easily explode. Therefore, when installing spotlights, it is necessary to install transformers that can effectively prevent explosions.
2, pay attention to install the spotlight
In the selection of lamps and lighting must be appropriate, especially spotlights. If blindly pursuing the number of spotlights, it will create light pollution and it is difficult to achieve the desired decorative effect. At the same time, placing too many spotlights is more likely to cause fire hazards.
Decoration Material Knowledge Chandelier House Decoration Interior Decoration Space Lighting Decoration Living Room Bathroom Door Bedroom Bedroom Lamp Bedroom Lamp
Cangzhou Youlong Pipe Fitting Manufacturing Co., LTD , https://www.ypco88.com